Product description
- Overhead sectional door/sectional door with panels of extruded, E6-EV1, anodized, high strength aluminium profiles with a thermal separation as supporting frame (Height 450 - 700 mm).
- Life time expectations door: 200.000 door cycles if service/replacement program is performed.
- Infills optionally double or triple layered acrylic windows, double hard (energy) glass.
- Integrated finger pinch protection
- Top, bottom and side seals and seals between door sections
- Standard track system in galvanized steel
- Spring balancing, 20.000 cycles
- Spring break device
- Lock bolt, step-handle,
- Compliance with all operational and safety instructions in EU Directives and the standards of the European Standardization Committee (CEN)
- Standard hardware (head room 485/510 mm to 800 mm)
- Operating system: manual
- Standard door sizes (DLW x DLH)
MIN: 1200 x 2000 mm
MAX: 7250 x 6050 mm
CEN Performance
- Wind load (EN 12424): Class 3 (700 N/m²) door width ≤4.250 mm
- Thermal transmittance (EN 12428): 3,1 W/(m²∙K) with double acrylic glazing; 2,6 W/(m²∙K) with triple acrylic glazing; 2,2 W/(m²∙K) with double hard energy glass
- Water penetration (EN 12425): Class 3 (no passdoor)
- Air permeability (EN 12426): Class 3 (no passdoor)
Bottom Sections
- Standard: Aluminium insulated frame construction
- Option: Sandwich panel across entire width, surface waffled,
- Section height 545 mm plus bottom seal
Glazing infills
- Standard: scratch-resistant acrylic sheets, 2 x 2,5 mm, total thickness 27 mm, single sealed
- Option: acrylic sheets, 2 x 2,5 mm, total thickness 27 mm, single sealed
- Option: acrylic glass 2 x 2,5 mm, total thickness 27 mm, double sealed
- Option: scratch-resistant acrylic glass 2 x 2,5 mm, total thickness 27 mm, double sealed
- Option: Triple glazing – scratch resistant
- Option: Triple glazing – not scratch resistant
- Option: DH4D, double glazing 2 x 4 mm hardened glass (thermal transmittance glazing, 2,75 W/(m²∙K))
- Option: DH6D, double glazing 2 x 6 mm hardened glass (thermal transmittance glazing, 2,75 W/(m²∙K))
- Option: DE4D, double glazing 2 x 4 mm hardened glass with Argon filling (thermal transmittance glazing, 1,1 W/(m²∙K))
- Option: DE6D, double glazing 2 x 6 mm hardened glass with Argon filling (thermal transmittance glazing, 1,1 W/(m²∙K))
Sandwich units
- Standard: infill, aluminium units, surface stucco interior / exterior
- Option: infill, steel units, interior / exterior RAL 9006 surface smooth
- Option: infill, aluminium units, surface aluminium stucco interior / exterior smooth
- Option: infill, aluminium units interior / exterior anodized
(Other glazing / sandwich unit designs available on request)
Surface color
Insulated aluminium frame
- Standard: E6/EV1 anodized
- Option: interior and / or exterior painted in standard colors
- Option: interior and / or exterior painted in RAL-standard color buyer’s choice
- Option: interior and / or exterior painted according to color sample
- Option: interior and exterior powder coated
Sandwich panel
- Standard: Aluminium panel aluminium interior and exterior or
- Standard: Steel panel interior RAL 9002, exterior standard colors
- Option: Aluminium and steel panel interior and/or exterior painted according to color sample
- Option: Aluminium and steel panel interior and / or exterior painted in RAL-standard colors buyer’s choice
Infills
- Standard: Design see above
- Option: interior and / or exterior painted in standard colors
- Option: interior and / or exterior painted in RAL-standard color buyer’s choice
- Option: interior and / or exterior painted according to color sample
- Option: interior and exterior powder coated
Door locking device
- Option: Second lock bolt
- Option: Lock with profile cylinder lockable on one or both sides
- Option: Door locking switch (essential with electric operation)
Hardware
- SLL: drop clearance 400 mm
- LL: drop clearance 265 mm (≤250 kg), 300 mm (>250 kg, >6000 mm)
- HL: drop clearance HL+320 mm (HL ≤3400 mm), HL+370 mm (HL >3400 mm)
- HHL: drop clearance HL+220 mm (HL ≤3400 mm), HL+270 mm (HL >3400 mm)
- VL: drop clearance min. door height + 400 mm
Operator
- Option: Chain hoist “T” (Gear ratio 1:4, Door weight max. 250 kg)
- Option: Chain hoist “U” (Gear ratio 1:3, Door weight over 250 kg)
- Option: Electronic operator:
- Operating voltage: 230 V AC, 50/60 HZ (internal supply 3-phase 230 V AC)
- Operating factor: ED = 30%, S3 10 min, non-continuous operation
- (Engine operation 3 min, pause 7 min, direct-inverting)
- Torque: 15-40 Nm, depending on reel type (value of given door shaft)
- Fusing: 10 A
- Brake: non-reversible worm gear
- Speed monitor: electronic monitoring
- Freewheel / clutch: mechanical engagement/disengagement
- Limit switch: electronic via torque (setting “Door open” during programming) Setting “Door closed” in processor board
- Gears: worm gear 1750 RPM yields approx. 24 rotations door shaft
- Shaft: ø35 mm or hexagonal
- Direct drive system
- No special wall reinforcement necessary
- Temperature range: -20°C to 60°C
- Soft stop, soft start
- Connection using “CEE plug” or lockable mains isolator
- Maximum door weight 400 kg
- Options
- Chain transmission
- Chain guard
Other drive variants available on request subject to technical inspection
Control units
Control unit 920
- Output 0.37 kW, input 1 x 230 V. Including control unit with standard actuator UP‑STOP‑DOWN. The door closes using dead-man controls.
- Operating speed 0.25 m/s, safety rating IP 55. If there is a power failure, the disengage device enables manual operation at any time
- Options:
- Additional buttons, key switch
- Door/bridge interlock
Control unit 930
- Output 0.37 kW, input 1 x 230 V. Including control unit with standard actuator UP‑STOP‑DOWN. The door closes using pulse control incl. self-monitoring safety edge
- Operating speed 0.25 m/s, safety rating IP 55. If there is a power failure, the disengage device enables manual operation at any time
- Options
- Radio remote control
- “Open” (if open button is used during closing process - door immediately stops and opens completely)
- “Automatic close” (safety photo cell compulsory requirement)
- Door closes automatically after set period (4-60 sec)
- Pull switch for opening function
- External push-button, key switch
- Door/bridge interlock
Control unit 950
- Output 0.37 kW, input 1 x 230 V. Dimensions: 180 x 380 x 120 mm (wxhxd) including control unit with standard actuator UP-STOP-DOWN and pulse control incl. self-monitoring safety edge. Counter/error code display and servicing info display in top of control cabinet. Operating speed 0.25 m/s, safety rating IP 55. If there is a power failure, the disengage device enables manual operation at any time.
- Options:
- Radio remote control
- “Open” (if open button is used during closing process - door immediately stops and opens completely)
- “Automatic close” (safety photo cell compulsory requirement) Door closes automatically after set period (4-60 sec)
- Pull switch for OPEN / CLOSE
- External push-button, key switch
- “One-button function” - opens or closes door, depending on actual status (e.g. radio, pull switch)
- additional safety (e.g. photo cell, radar) – door immediately opens completely
- D-Module (D1-D6)
- Photo cell
- Reduced opening height
- Radar
- Magnetic loop
- Warning lights
- Traffic lights
- Interlocking door function
- Door/bridge interlock
Other supplementary equipment
- Anti-corrosive hardware
- Anti-corrosive package Type “C”
- Stainless steel hinges and roller brackets
- Stainless steel screws
- Stainless steel roller shafts and door cables
- Aluminium top and bottom profile
- Powder coated corner bracket (RAL 9002)
- Anti- corrosive package Type “A”
- Stainless steel hinges and roller brackets
- Stainless steel screws
- Stainless steel roller shaft and door cables
- Aluminium top and bottom profile
- Powder coated corner bracket (RAL 9002)
- Powder coated end caps, trusses, tracks, hangers, connection beams, safety pull bracket (RAL 9002)
- Anti- corrosive package Type “S”
- Safety pull cables, stainless steel
- Anti- corrosive package Type “Z”
- Electro-galvanized springs (max. 70.000 cycles)
- Cable break device
- Increased cycle spring (20.000 – 100.000)
- Ventilator “P” (free area approx. 170 cm²)
Special models
- Fixed top and side sections, with and without passdoor, in the same color and construction as the door leaf are available on request !! (subject to technical inspection)
