Angle Flange Adapter 18ga

Nordfab manufactures ducting for use in dust, mist, and fume collection systems.

Nordfab’s Quick-Fit® 18 gauge Angle Flange Adapter is fitted with an industry standard Angle Flange on one end and a Quick-Fit (QF) rolled edge at the other, allowing quick connection of QF duct pipe or fittings to flanged pipes or fittings.

If a custom bolt hole pattern is required, specify a Flat Flange (FFL) instead of an Angle Flange (ANGFL) and provide the hole pattern. If no hole pattern drawing is provided, flat flange will be blank. Flanges are retained with a Van Stone lip allowing easy rotation and alignment during installation.

Available in galvanized steel and 304SS (as shown below) or optional 316SS or carbon steel
Available with flanged ends in diameters up to 72", and other various end types
Optional gauges 22 and 20, 16, 14, 12 and 10

Contact Nordfab or your local Nordfab dealer for assistance with larger sizes and material / gauge options.

Quick-Fit has been used in a wide variety of applications, wherever dust collection or fine particulate transfer is required. Quick-Fit saves time and money on installation, is easy to clean out, is adaptable to existing ductwork, and is easily re-used during shop floor reconfigurations. Learn more about why Quick-Fit may be the best solution for you.

Специфікація

A. General Fabrication Requirements: Comply with SMACNA's "HVAC Duct Construction Standards - Metal and Flexible," Ch. 3, "Round, Oval, and Flexible Duct," based on indicated static-pressure class unless otherwise indicated.
1. Construct ducts of galvanized sheet steel unless otherwise indicated. 304SS Optional.
2. Basis-of-Design Product: Subject to compliance with requirements, provide Nordfab Ducting, LLC; Quick Fit (QF) Duct.
B. Connection Joints: Joint types are fabricated in accordance with SMACNA's "HVAC Duct Construction Standards - Metal and Flexible," for static-pressure class, applicable sealing requirements, materials involved, duct-support intervals, and other provisions in SMACNA's "HVAC Duct Construction Standards - Metal and Flexible."
1. Quick Fit Joints in Ducts 3 to 24 inches (76 to 510 mm) in diameter. Flange: Optional.
2. Flanged Joints in All Ducts Greater than 24 inches (610 mm) in diameter.
C. Longitudinal Seams: Seam types are fabricated in accordance with SMACNA's "HVAC Duct Construction Standards - Metal and Flexible," Figure 3-2, "Round Duct Longitudinal Seams," for static-pressure class, applicable sealing requirements, materials involved, duct-support intervals, and other provisions in SMACNA's "HVAC Duct Construction Standards - Metal and Flexible."
1. Fabricated round ducts 3 to 24 inches (76 to 510 mm) in diameter to have laser-welded or plasma-welded longitudinal seams.
2. Fabricated round ducts above 24 inches (610 mm) in diameter to have plasma-welded longitudinal seams.

Технічна специфікація

Унікальний номерangle-flange-adapter-18ga
Сімейство продуктівQuick-Fit Clamp Together Ducting
Група продуктівAdapters
ТипObject (single object)
Дата публікації2024-05-08
Номер видання1

Посилання

Url-адреса продуктуhttps://www.nordfab.com/en-us/products/qf-ducting/adapters/angle-flange-adapter-18ga
Технічний описhttps://www.nordfab.com/-/media/files/nordfab/americas/americas-product-data-sheets/nordfab_angle_flange_adapter.pdf

Пов'язані

Матеріал основнийGalvanized steel
Матеріал допоміжнийStainless steel 304
Розроблено вСполучені Штати
Виготовлено вСполучені Штати

Класифікація

Категорія BIMobjectHVAC - Dust Collection
Класифікація IFCDuct Fitting
Код за ETIMEG015540
Назва за ETIMFittings, flanges and connectors
Код Uniclass 2015Pr_65_65_25
Опис Uniclass 2015Ductwork and fittings
Код CSI MasterFormat 201423 31 13.19
Заголовок CSI MasterFormat 2014Metal Duct Fittings
Номер OmniClass23-33 49 00
Заголовок OmniClassHVAC Ductwork

Доступність регіону

Північна Америка
Беліз
Бермудські Острови
Британські Віргінські острови
Канада
Коста-Рика
Мексика
Панама
Пуерто-Рико
Сен-Мартен
Сполучені Штати